gallery/paypal logo

CustomDUO modules

Fitting CustomDUO Modules 

Prior to fitting it is of course necessary to remove original reflector, bulbs, LED modules, etc. Unscrewing the grey bezel in order to remove the front window can sometimes prove challenging if Duo has been left to rot, but inevitably they do come off. (Hint, if you can't do it then find someone with strong hands. The trick is to squeeze and turn at the same time !!!)

 

CustomDUO Omni modules are a simple push fit into the Petzl Duo lamp housing. Electronic connection is via the 2 pins on reverse of module which locate in the Duo bi-pin bulb / LED connection socket. Orientate Omni module in the body of your Duo, aligning the contact pins, and push fit module into place. Ensure the module is sat down fully in Duo body. Test operation of module. If module does not work immediately, then read about battery polarity below.

 

To conclude, refit the Duo front window. Some silicone grease on the seal and threads is always a good idea. Holding window in position with thumb, refit the grey plastic bezel until the Petzl correct fitting alignment marks (on top of the lamp) are correctly orientated. The marker formed on the grey screw bezel needs to be somewhere in between the two markers formed on the top of the yellow lamp body. 

Omni Module Fitting (v5 and Simple) 

CustomDUO LED upgrade modules will work with all variants of the original pre 2018 Petzl Duo. Modules are not available for the new 2018 DuoZ and DuoS, which are factory sealed and not designed to be upgradeable in the future as LED technology advances.  

Polarity

 
Very occasionally we come across an early (pre 2004) Petzl Duo which has been wired up back to front, and the polarity is wrong for the Customduo LED modules. This affected some, but not all early Duos, and these Duos are now extremely rare. Polarity conscious LEDs hadn't been considered at this time so it wasn't important which way around the positive and negative were wired at manufacture. If you fit your CustomDUO module and it does not immediately work, chances are that your Duo is wired up back to front. The solution is simple. Reverse the batteries in the battery holder, i.e. positive to negative, and vice versa. The module will then work. CustomDUO modules are polarity protected, so you will not have damaged the module by finding this out. 

 

Alternatively, for the electronically skilled, the Omni modules features solder jumpers that allow the polarity of the module to be reversed. Note, if you have suitable electronic skill to undertake this then you should be able to locate the circuit board jumpers without our help! 

 

 

Batteries, power and light output 

 
As standard, the Petzl Duo uses 4xAA batteries. It is important to note that the highest power settings of the Omni v5 module, i.e. 700mA flood and 700mA spot, 1400mA combined, may not be achievable dependant on battery type (NiMh or Alkaline), battery quality / condition, and level of charge. Lamp condition is also a factor. If the batteries cannot deliver e.g. the 1400mA required, the lamp will operate as normal, but not at full brightness. The slight upside of this is that reduced power draw from batteries by default will result in extended operating durations. 


In our opinion, 1400mA is at the limit of what can be realistically achieved with Petzl Duo and the best AA cells, given the battery technology currently available. For best result we suggest low self discharge NiMh batteries, such as the 'Eneloop' brand. 

 

The regulated power settings levels for modules are given in mA. To determine the approximate regulated duration of light on your battery arrangement at a given power setting, simply divide the mAh capacity of your cell pack by the mA power draw at a given setting. For example, using 2100mAh NiMh low self discharge AA batteries at a power setting of 350mA will give a regulated duration in the region of 5-6 hours.

 

We are occasionally asked if it is possible to run CustomDUO modules from Li-ion battery packs typically constructed from 18650 cells. The modules will run very well at 3.7v, for example a single 3.7v li-ion battery or a number of cells parallel wired. The only small issue to note is that battery charge level indicators are set up for  4xAA batteries, so will not provide an accurate indication of battery charge level. Series wired cells, forming higher voltage packs, for example 7.4v are not suitable and will likely damage the modules (which are limited to 6 volt max). We are not convinced that this is the best idea ever, but it is possible to fit 2 x 18650 cells into a stripped out Duo box. It's very tight though, you have been warned.  

 

  

 

gallery/fixo9

Gecko 'Side' Modules are a simple push fit, much the same as the Omni modules. Electronic connection is via the 2 pins on reverse of module which locate in the Duo bi-pin bulb / LED connection socket. Orientate module in the body of your Duo, aligning the contact pins, and push fit module into place. Test operation of module. If module does not work immediately, then as above, see notes on battery polarity. Some (but not all) early pre 2004 Petzl Duos were wired to the opposite polarity, but is very easily solved, see battery polarity below.

 

Gecko Module Fitting (v3 Spot and v3 Side) 

The Gecko Side module is designed to be fitted with Gecko Spot module. Gecko Side modules can also be fitted with standard Duo halogen bulb and 14 LED reflector, though this is not common practice. 5 LED reflector will require a small amount of trimming to accomodate Gecko side module.   

 

The Gecko Spot module is designed to fit seamlessly with Gecko Side module. Gecko Spot can also be fitted with Petzl modu'led units 5-14 LEDs, though this is again not common practice. 

 

The Gecko v3 Spot module uses an innovative 3 pin arrangment to connect into the Duo lamp housing via the original halogen bulb connection. See Gecko v3 Fitting Guide

gallery/img_3975
gallery/geckspot20143
gallery/geckohalogen